Creating Tapered Plate Girders in MasterFrame
Posted on October 25th, 2019 in Analysis
Summary
The sources detail a process, or "trick," for creating tapered plate girders in MasterFrame software, circumventing limitations present when trying to taper standard built-up sections.
Standard Limitations and the Workaround
A typical portal frame utilizes standard serial size beams, such as UBs or European IPEs, which can easily be set as uniform or tapered sections. However, if a standard UB section is changed to a built-up section (a plate girder), the user can define the dimensions (e.g., 500 or 530 deep, 215 wide), but they lose access to the standard tapered sections because these sections are "normally not meant to be tapered".
The solution involves applying a trick: creating a custom section group and section sizes within an open library, and then applying the taper to that newly defined custom section.
Step-by-Step Process for Creating a Tapered Plate Girder
The process begins by moving away from the default database, which is rigorously controlled by Master Series, and switching to a custom database (e.g., "database one").
1. Define the Custom Section Type (PLT): The user must access the editor by navigating through 'Edit, Open Library,' and then 'Edit' again, going to 'Section Types'.
- A new section is added and named PLT.
- The category for this section is designated as an I section.
- The section ID is set to 31 (though it might appear as section 42 in the list).
- The section is marked as "not hidden".
- This new section type is then saved and added to the list.
2. Define Specific I-Section Sizes: The next step is to move to the I-sections area, where the newly created PLT section will be listed alongside the standard I-sections.
- A new section size is added, for example, section number 900.
- The section type is assigned as PLT.
- Specific dimensions are input, such as a depth of one metre, a breadth of 200, a web thickness of 12 mm, and a flange thickness of 25 mm plates.
- Setting the root radius as zero classifies the section as a welded section.
- The section properties are calculated.
- Crucially, if the section is going to be used as a tapered section, the weight calculation can be removed from the input.
- The values are then saved in the database.
- Additional section sizes (e.g., 902) can also be created following similar steps.
3. Applying the Taper to the Member: Once the custom PLT sections are available, they can be applied to a member, such as a column in a portal frame.
- Under the member's properties, the PLT section (e.g., the 1000 initial section) is selected.
- The member is then designated as tapered.
- A single taper can be defined by specifying the initial depth and the final depth. For example, tapering a column from an initial depth of 1000 down to 300 at the bottom and 650 (0.65) at the top. This creates the tapered plate girder.
Constraints on Tapering
When attempting to define a partial taper (using taper lengths), the sources note a significant constraint: the section cannot be defined as shallower than the default section. Therefore, to execute a full taper, both the initial taper and final taper values should be set to zero. If the design requires tapering in two separate parts, two distinct members must be created.
Furthermore, if the built-up section is defined as shallower than the default 1000 mm depth, the software assumes only the two flanges in these instances. This contrasts with standard serial sizes, where a middle flange is assumed when the depth is defined as greater than one.
Summary with Timestamps
This summary draws on the provided excerpts detailing the creation of tapered plate girders in MasterFrame using a specific workaround, as standard built-up sections are typically "not meant to be tapered".
The following table summarises the process and constraints involved in defining a custom section type (PLT) and applying a taper to it.
| Time Stamp | Summary Point |
| 00:00:08,000 – 00:01:12,800 | Context and Limitation: Standard portal frame members (UBs or European IPEs) easily allow for uniform and tapered sections. However, if a standard UB section is changed to a built-up section (plate girder), the ability to access and apply standard tapered sections is lost, even though dimensions can be defined (e.g., 500 or 530 deep, 215 wide). |
| 00:01:13,520 – 00:02:20,480 | The Workaround Setup: A "trick" must be applied by creating a custom section group and section sizes within an open library, which can then be tapered. The user must first switch from the default database, which is "rigorously controlled by Master Series," to a custom database (e.g., "database one"). The editor is accessed by navigating to 'Edit, Open Library' and then 'Edit' again, going to 'Section Types'. |
| 00:02:22,200 – 00:03:21,360 | Step 1: Define Section Type (PLT): A new section type called PLT is added. It is designated as an I section and assigned Section ID 31 (which might appear as 42 in the list). The section is marked as "not hidden" and saved to the list. |
| 00:03:22,640 – 00:05:25,440 | Step 2: Define Section Sizes: The user moves to the I-sections area where PLT is now listed. A new section size, such as section 900 (type PLT), is added. Specific dimensions are input, such as a depth of one metre, breadth of 200, web thickness of 12 mm, and flange thickness of 25 mm plates. Setting the root radius as zero classifies it as a welded section. The section properties are calculated, and the user can optionally remove the weight calculation since it will be used as a tapered section. The values are then saved in the database. Another section size (902) can also be created similarly (e.g., using 20 mil plates). |
| 00:05:28,320 – 00:06:48,000 | Step 3: Applying the Taper: The custom PLT section (e.g., the 1000 initial section) is selected for a member (like a column). The member is defined as tapered. A single taper is set, defining the initial depth (e.g., 1000) and the final depths (e.g., 300 or 0.3 at the bottom and 650 or 0.65 at the top). Both the initial taper and final taper values are set to 0. This successfully inputs the plate girder as a tapered section. |
| 00:07:30,800 – 00:08:25,360 | Tapering Constraints: When defining a partial taper (using taper lengths, e.g., 4 meters and 3 meters), the software presents a problem: the section cannot be defined as shallower than the default section. Therefore, to achieve a full taper, the initial and final taper values must be set to zero. If the design requires tapering in two separate parts, two distinct members must be created. |
| 00:08:28,800 – 00:08:57,120 | Software Assumptions: When the built-up section is defined as shallower than the default 1000 mm depth, the software assumes just the two flanges. This contrasts with standard serial sizes where, if the depth is greater than one, the software assumes a middle flange. This simple process allows for the creation of a tapered plate girder. |